MTB Parts Catalog Link Section

Bigger, grippier, lighter and as tough as ever. The Penthouse Flat MK5 pedal is here! After two years of development and testing the MK5 Penthouse Flat is here. Retaining our signature toughness, the MK5 is the lightest and grippiest Burgtec pedal to date. We did this by not only increasing the size of the pedal platform but also how concave it is. Furthermore, we reduced the diameter of the pins and added the most wear-resistant internals on the market. From the outside to the inside, we've sweated the details of the MK5 to bring you the ultimate flat pedal. - Weight: 379g - Platform material: 7075 Alloy - Profile: 15mm - Platform: 100mm x 102mm - Dish: 2mm (concave) - Pin material: Stainless steel - Pin width: 3.5mm - Pin height: 4.5mm - Axle Material: EN24T Steel - Internals: 2 x Igus W300 bushings, single sealed bearing and inboard rubber oil seal

An energetic cosmopolitan! Tires are a safety-relevant component of each bicycle. High speeds and the additional weight from the battery and drive of an e-bike of up to 50km/h make a special e-bike tire necessary. A high-quality additional rubber 3/180 TPI reinforced carcass forms the solid frame of the E.CONTACT. The SafetyPLUS Breaker puncture protection specially developed for the high demands on e-bikes, protects the tire reliably against punctures and cuts. The profile of the tire is just as at home on asphalt as on gravel and forest trails — a good all-around tire.

The Newton MTR (Mountain Rear), part of our ultimate tire package developed for gravity riding & racing. A tire that is at its best bringing up the rear while sprinting out the start hut of your race run, as you attack those loose off camber sections, hold the line on rocky chutes and pinballing down rock sections. Who Rides This Tire? Your bike of choice is a Downhill, Enduro or trail rig, you eat/sleep loose turns, berms and full-on terrain. Where Does This Tire Perform Best? Best suited to your rear wheel. A broad range of conditions from loose dust to wet loam. Most at home on Downhill & Enduro terrain, or rowdy trails. Go Faster, Go Bigger The tire, that small contact patch that connects you to the ground, is arguably the most important part of your bike. When you’re in the start hut, about to drop into your race run you need to know that this essential component is designed specifically with the job in mind. What better choice than the tire named after the man who defined the very laws of gravity. For Downhill, Enduro, and trail Dominance Drive focused tread delivers speed and durability with tracking performance that inspires confidence transitioning from straight-line to cornering across a wide range of conditions. Construction A dual-ply, 120TPI construction, the 2x120TPI casing is supple and fast rolling with improved traction while providing high levels of support Grip3 Compound Rear specific, triple density 40/50/60a compound, offering balanced levels of grip and treadwear. Protection EN:Wall – A butyl layer located within the casing ply that provides defence to cut and abrasion as well as providing extra sidewall support.

- Lug pattern designed to give greater progressiveness, terrain versatility and maximum grip when braking - New 3x33 TPI casing with high-density fibers, lighter, more comfortable and robust, tailored to Enduro racing - Maximum durability with the new Gravity Shield casing, offering greater ride comfort - A tire co-developed with and validated by the world's best EWS riders - Rear-specific tread design

- Comfortable ride - Classic colors

Service kits include dust seals, foam rings, oil seals, air and damper o-rings needed for basic service.

- Unidirectional carbon fiber riser bar with 35mm stem clamp area - Downhill strength with 25% weight savings compared to aluminum

- Recreational tire with raised center for low rolling resistance - Fits Schwinn "lightweights" and older British club bikes - Size: 26 x 1 3/8

- Plastic nylon molded body - Chromoly spindle - 318g pair

Dimension Junior Pedals. - Molded nylon, 1-piece, caged-type pedals - Built-in reflectors, will not accept toe clips - Overall pedal size is 80 x 60mm - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 230g (9/16-inch); 304g (1/2-inch)

- High impact Resin multi-use body with integrated cage - Externally sealed ball bearing system - 100mm x 82mm platform - Weight: 316g pair (9/16")

- Protective neoprene and velcro cut-To-Fit boot fits most rear shocks

• Lightweight aluminum construction • Back sweep: 6 degrees

- One-piece resin body and cage - Toe-clip compatible

The Tour is a great budget urban or touring tire. Offered with or without reflective sidewalls for extra nighttime cycling safety. Excellent wet weather tread. - Wire bead

- One-piece resin body - Chromoly spindle - Toe clip compatible - 366g pair

- Urban/recreational tire with shallow, grooved tread for multiple conditions

• Sturdy, chrome-plated steel construction • Back sweep: 6 degrees

- One-piece ABS resin body - Molded pins - 320g pair

- One-piece nylon body - Chromoly spindle - Toe clip compatible - 407g pair

- One-piece resin body - Juvenile size platform - Boron spindle - 390g pair

The Thermalite pedals feature a concave, low profile design and are molded with Thermalite nylon material. - Micro knurling with 24 pins for traction - Recessed end to prevent damage to bearing cover - Chromoly spindle with 6mm broach and 15mm wrench flats - Weight: 391g - Pedal Body Material: Composite/Plastic

- Clamps on to dual-Crown fork stanchions to prevent damage to frame - Easy to install and adjust, More secure and lower profile than stock bumpers - Molded loops allow clean and easy zip-Tie number plate mounting - Available for 35mm boxxer or 40mm fox stanchions, Sold in pairs

- One-piece ABS resin body - Non-slip rubber surface - Boron spindle - 388g pair

Sturdy steel construction with a versatile riser bar style.

- One-piece resin body with rubber surface for grip - Boron spindle - 400g pair

Dimension Mountain Basic Pedals. - Molded nylon 1-piece, caged-type pedal with reflectors - Accepts toe clips - Hang tag packaging - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 330g

- One-piece resin body - Barefoot friendly rubber surface - Includes reflectors

The Dak pedals are the Dakota Roche signature model that feature 14 large hexagon molded pins on both sides for maximum grip. - Slim profile - Large surface area - Heat treated 4130 spindle - 9/16"

- Long-lasting, high-quality rubber compound - Center tread siping for enhanced wet road traction - Continuous center tread for a smooth ride